Warehouse & Industrial Concrete Floors in Jacksonville, FL
Flat, hard-wearing interior slabs for the Port of Jacksonville logistics corridor. Built for racking, forklifts, and heavy equipment.
Industrial floors for Jacksonville's logistics corridor
Jacksonville's warehouse and distribution boom, driven by JAXPORT and the I-295 and I-10 logistics corridor, runs on concrete floors that stay flat under racking and take forklift traffic all day. An industrial floor is the hardest-working slab on the property, and it has to be built to the loads and the flatness the operation needs.
Our minimum commercial spec is a 6-inch, 4,000 PSI slab on a 6-inch compacted base with #4 rebar on 18-inch centers, over a vapor barrier that matters in Florida's high water table and humidity. For heavy forklift and racking applications we increase to 6,000 PSI with closer rebar spacing and fiber reinforcement, plus a dry-shake hardener where abrasion resistance is required.
We hold FL Certified Building Contractor license CBC1269043, coordinate mix-design documentation and inspections, and can pour large placements in a single day to limit downtime for your operation.
Scope of work
New Warehouse Floors
Interior slabs on grade poured to the structural drawings for distribution, storage, and manufacturing.
Forklift & Racking Slabs
Thicker, heavily reinforced slabs where concentrated post and wheel loads demand it.
Surface Hardeners
Dry-shake metallic or mineral hardeners troweled in for abrasion resistance in high-traffic aisles.
High-Flatness Floors
Floors finished to a specified F-number for pallet-jack and narrow-aisle racking operations.
Joint Repair & Filling
Failed joints and spalled edges rebuilt and filled with semi-rigid filler to protect forklift wheels.
Slab Replacement
Selective saw-cut, demolition, and re-pour of failed sections without tearing out the whole floor.
What does a warehouse floor cost in Jacksonville?
Industrial floor pricing depends on slab thickness, reinforcement, flatness spec, and whether a hardener is called for. Typical ranges below.
Standard industrial floor
A reinforced interior slab typically runs $13 to $18 per square foot, including a rebar mat, hard-trowel finish, and joint work.
Hardened / high-flatness floor
Floors that need a dry-shake hardener or a tighter F-number for narrow-aisle racking sit at the upper end and above.
Slab repair & joint filling
Spall repair, joint filling with semi-rigid filler, and section replacement are quoted per the condition of the floor.
Our commercial process
Drawings & Load Review
We review the structural slab drawings and loads, then confirm thickness, reinforcement, and flatness.
Base & Vapor Barrier
We compact the sub-base and place a vapor barrier, which matters in Jacksonville's high water table and humidity.
Reinforce & Pour
Rebar mat on chairs, dowels at joints, then pump or direct placement with a laser screed for flatness.
Finish, Harden & Cure
Hard-trowel finish with a dry-shake hardener where specified, cure per ACI, then saw-cut and fill joints.
Frequently Asked Questions
How thick should a warehouse floor be?
A typical warehouse slab runs 6 to 8 inches, while floors carrying heavy racking and forklift traffic often go to 8 to 10 inches with a heavier reinforcement mat. The structural engineer sets it from the rack and wheel loads.
How much does an industrial floor cost in Jacksonville?
A reinforced interior slab typically runs $13 to $18 per square foot, including the rebar mat, hard-trowel finish, and joint work. Floors that need a hardener or a tighter flatness number cost more.
Why does a vapor barrier matter in Jacksonville?
Florida's high water table and humidity push moisture up through a slab, which can damage flooring, coatings, and stored goods. A vapor barrier under the slab blocks that moisture, and we install one wherever the floor calls for it.
What is a dry-shake hardener and do we need one?
It is a metallic or mineral topping troweled into the fresh surface for abrasion resistance. High-traffic aisles and heavy-use floors benefit; lighter-duty storage floors often do not need it.
Can you replace a failed section without tearing out the whole floor?
Yes. We saw-cut and remove the failed area, correct the base, dowel into the surrounding slab, and re-pour just that section so it ties in level.
How flat does the floor need to be?
That depends on the racking and equipment. Standard floors are finished to a straightedge tolerance, while narrow-aisle floors need a measured F-number. We confirm the flatness spec up front and finish to it.
Get a written quote on your commercial project
FL Certified Building Contractor CBC1269043. Licensed and insured. Serving Jacksonville and all of Duval County.
☎ Call (904) 664-6905